4/14/2023 0 Comments Duplicate stitch knittingShe also explains how to easily remove the surface chains from the project if you make a mistake or want to change the design. This secures the last chain, and the tail is brought to the Wrong Side so that it can be woven into the project. Once the chains are complete, Mary Beth demonstrates how to finish off the chain, by bringing the yarn tail through the final chain to the front of the work. The yarn overs can be created at the back while the Right Side is always facing. She demonstrates the yarn over worked on the back of the piece by flipping over her knitted fabric to the Wrong Side but notes that it is not necessary to flip your fabric over. ![]() This process is repeated to make several chains. She then goes into the center of the next stitch from front to back, works a yarn over, and pulls it through with the hook to the front, the brings the loop through the other loop on the hook to create a chain. She works a yarn over onto the hook and pulls the hook back through to the front of the work. ![]() She takes the crochet hook into the center of a stitch from the front of the work to the back. To begin, Mary Beth holds the yarn to the back of the work, leaving a 4 to 6-inch tail that will be woven into the project once it is complete. The surface chains are created by using a contrasting color yarn and a crochet hook that is similar in size to the knitting needle used for the project. For embroidery that’s worked horizontally, she prefers to use duplicate stitch. Leave a good long tail, as we’ll weave this in at the end, Here I am working Row 4 going left to right. Mary Beth suggests using this surface chain technique for designs that have long vertical columns. 1) Start by bringing your needle back to front through the base of the stitch the bottom point of the V. In this video, crochet expert Mary Beth Temple shows you how to use a crochet hook to create surface chains to embroider your knitting. Happy knitting from your friends at AlpacaDirect.There are many ways to embroider and embellish your knits. This is a great technique that can help you to troubleshoot lots of different problems in knitting. If you have one purl that should have been a knit in ribbing just duplicate stitch over it! ![]() If you're working fair isle and worked a stitch in blue that was supposed to be white, just duplicate stitch over the erroneous stitch with the correct color. The duplicate stitch is also used to make colorwork patterns, and can also be used to fix other common mistakes. Do not cut without weaving them in! If you cut your ends without weaving them there won't be any friction to keep the yarn from falling out and exposing your split stitch again. Just weave these in through your work just like any other end. On the back you'll see there are some ends. As you can tell the stitch in white is indistinguishable from the other stitches. On the right is the duplicate stitch in yellow, and on the left in white. And Voila! There's no longer a hole in the knitting! Step 12. Pull the yarn through and re-insert back into your original starting point at the base of the stitch. Then work your needle underneath both sides of the stitch above, tracing the yarn with your needle. Follow the same steps, place the needle from the wrong side through to the front at the base of the stitch. Now you've duplicated your stitch! Now it's time to do it with the same color yarn as the swatch and cover up the split stitch. Now thread the yarn through the same spot where you started your duplicate stitch-in the base of the stitch, and pull through to the wrong side. You'll see that we've already duplicated the right side of the stitch. Be sure to go under both sides of the stitch. Thread the tapestry needle underneath the stitch above. Pull the yarn through the base of the stitch. With the duplicate stitch method you are embroidering over a stitch, duplicating the yarn and placing another stitch on top of the one that was knit. This fix is so invisible that if we demonstrate it with white yarn there won't be anything to see! Start by threading your tapestry needlewith yarn and poke your needle through from the wrong side at the base of the stitch that you wish to duplicate. First we'll show you in another color yarn. So prevent the hole from forming at all! Today we're going to show you how to duplicate stitch over your split stitch to reinforce the area and hide the split stitch. If your item is going to get lots of wear (which we're sure it will!) this spot is the first place that's likely to get a hole in it. It'll create a bit of a hole in your knitting, but more importantly, this is a weak point in your knit fabric. This happens when you don't grab the whole strand when knitting a stitch. What's a knitter to do? Re-knitting the whole item doesn't seem like a reasonable option, but don't worry, there's a much easier fix! Sometimes you'll find that you've split a stitch long after binding off when knitting.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |